Skip to main content

Basic PLC Ladder Programming Examples 22

 Basic PLC Ladder Programming Examples 22

Basic PLC Ladder Programming Training Examples for Beginners.  Hi friends, here we are starting unique a series of Free Training on PLC Ladder Programming & tutorials. These PLC Ladder Programs are important to learn basics of Ladder programs.

Basic Program Designing Example 1:

Start, Stop and Latched In some application occasions, we need to use the transient close/open buttons for the start and stop of an equipment. To maintain its continuous action, you have to design latched circuits. Example 1: Stop first latched circuit When the normally open contact X1 = On and the normally closed contact X2 = Off, Y1 will be On. If you make X2 = On at this time, Y1 will be Off. It is the reason why this is called “stop first”.




Example 2: Start first latched circuit

When the normally open contact X1 = On and the normally closed contact X2 = Off, Y1 will be On and latched. If you make X2 = On at this time, Y1 will continue to be On because of the latched contact. It is the reason why this is called “start first”.



Example 3: Latched circuit for SET and RST instructions

See the diagram in the right hand side for the latched circuit consist of RST and SET instructions. In the stop first diagram, RST is placed after SET. PLC executes the program from up to down, so the On/Off of Y1 will be determined upon its status in the end of the program. Therefore, when X1 and X2 are enabled at the same time, Y1 will be Off. It is the reason why this is called “stop first”. In the start first diagram, SET is placed after RST. When X1 and X2 are enabled at the same time, Y1 will be On. It is the reason why this is called “start first”.



Example 4: Power shutdown latched

The auxiliary relay M512 is latched (see instruction sheets for DVP series PLC MPU). The circuit can not only be latched when the power is on, but also keep the continuity of the original control when the power is shut down and switched on again.



 Example 5: Conditional control

X1 and X3 enables and disables Y1; X2 and X4 enables and disables Y2, and all are latched. Due to that the normally open contact of Y1 is connected to the circuit of Y2 in series, Y1 becomes an AND condition for Y2. Therefore, only when Y1 is enabled can Y2 be enabled.



Example 6: Interlock control



If we serially connect the normally closed contact of Y2 in example 5 to the circuit of Y1 as an AND condition for Y1 (as the diagram in the left hand side), the circuit can not only make Y1 as the condition for Y2, but also allow the stop of Y1 after Y2 is enabled. Therefore, we can make Y1 and Y2 execute exactly the sequential control.


 See More PLC Ladder Programming Examples


http://news.chivindo.com/820/basic-plc-ladder-programming-examples-22.html

Comments

Post a Comment

Popular posts from this blog

SketchUp Pro 2020 v20.1.235 Full Version

BAGAS31 – SketchUp Pro 2020 v20.1.235 Full Version  merupakan software yang dirancang untuk membantu sobat membuat dan mengedit model 3D. Dengan desain tampilan yang ‘clean’ dan simple, menjadikan software ini mudah untuk digunakan. Software ini hadir dengan editor bawaan yang memungkinkan sobat mendesain objek 3D dari awal, Layout designer untuk menggabungkan model 3D serta Style Builder untuk menyesuaikan model dengan gaya yang berbeda. Software ini juga memiliki fitur untuk mengimpor data dari format lain, seperti 3DS, DWG, KMZ, JPG, PNG, PSD, TIF, TGA dan sebagainya. Tanpa berpanjang lebar, silakan download  Sketch Up Pro  versi terbaru 2020 v20.1.235 Full Version   melalui link yang disediakan. SketchUp Pro 2020 v20.1.235 Full Version Screenshots : Download : SketchUp Pro 2020 v20.1.235 Installer | Size: 128 MB [ FileUp ] | [ up4ever ] JAMU SketchUp Pro 2020 v20.1.235 Full Version | Size: 14.5 MB [ FileUp ] | [ ...
Post a Comment
Read more

SCADA

SCADA merupakan singkatan dari Supervisory Control and Data Acquisitio n. SCADA merupakan sebuah sistem yang mengumpulkan informasi atau data-data dari lapangan dan kemudian mengirimkan-nya ke sebuah komputer pusat yang akan mengatur dan mengontrol data-data tersbut. Sistem SCADA tidak hanya digunakan dalam proses-proses industri, misalnya, pabrik baja, pembangkit dan pendistribusian tenaga listrik (konvensional maupun nuklir), pabrik kimia, tetapi juga pada beberapa fasilitas eksperimen seperti fusi nuklir. Dari sudut pandang SCADA, ukuran pabrik atau sistem proses mulai dar 1.000an hingga 10.000an I/O (luara/masukan), namun saat ini sistem SCADA sudah bisa menangani hingga ratusan ribu I/O. Ada banyak bagian dalam sebuah sistem SCADA. Sebuah sistem SCADA biasanya memiliki perangkat keras sinyal untuk memperoleh dan mengirimkan I/O, kontroler, jaringan, antarmuka pengguna dalam bentuk HMI (Human Machine Interface), piranti komunikasi dan beberapa perangkat lunak pendukung. Semua itu...
Post a Comment
Read more

Persoalan Pokok pada Pembangkit Tenaga Listrik

Pembangkit listrik yang biasa digunakan pada suatu Sistem Tenaga Listrik (STL) terdiri dari pembangkit listrik tenaga air (Hydro plant atau PLTA) dan unit-unit thermal.Pembangkit-pembangkit itu sekarang ini umumnya sudah berhubungan satu dengan yang lainnya, atau yang sering disebut dengan interkoneksi. Setelah beroperasi dalam waktu tertentu, maka dari pembangkit-pembangkit itu ada yang keluar dari sistem interkoneksi dan hal ini disebabkan karena ada unit pembangkit yang rusak dan tentunya perlu diganti atau diperbaiki, kedua karena ada pembangkit yang istirahat untuk keperluan pemeliharaan. Salah satu contoh rencana pemeliharaan unit pembangkit adalah dengan menggunakan metode Levelized Resh dari Gaever . Namun dalam aplikasinya harus dibagi dalam dua kriteria, yaitu pertama unit pembangkit bisa dikeluarkan tanpa adanya penyesuaian. Kedua unit pembangkit yang dikeluarkan harus diatur dalam kurun waktu yang terbatas. Dengan demikian berarti pada waktu tertentu ada unit pembangkit y...
1 comment
Read more

Ferite Core Transformer

What are Ferrite Core Transformers? The transformer made out of ferrite core is called ferrite core transformer . The ferrite core transformer is used for higher frequency applications.The power transformer is made out of CRGO steel core which operate at 50 or 60 Hz frequency. The transformer operating at higher frequency is designed with a ferrite core. The composition of ferrite core in transformer is iron oxides,combined with nickle, zinc and manganese compounds. These compounds have low coercivity  and also called soft ferrites.   Advantage of use of  Ferrite Core ? A major advantage to a ferrite core is its high electrical resistance to high current. The high resistance to eddy current lead lower eddy current losses over many frequencies.  Ferrites have an advantage over other types of magnetic materials due to their high electrical resistivity and low eddy current losses over a wide frequency range. These characteristics, along with high permeability, make ferr...
Post a Comment
Read more

AIRCRAFT MAINTENANCE ENGINEERING'S APP BY MY INSTITUTION

The purpose of this post is introduce an app which introduced my department in polytechnics and developed by one of my lecturer. For my view of point, the app is mostly introduce about the course. So what about it? Let's take a look... In this post, I will introduce about the contents in the app by the phone screenshot which taken from my phone. I will share the way to get this app and the way to install in the end of this post. OK, let's take a look. First, can you guys and girls saw that is one app which named "DAM Students" in the phone screenshot? That is the app which today I want to introduce about. The icon of the app is the aircraft's model located in our hanger. In the front page of the app, you will see there is a few titles in the contents after you entered to the app. In the next screenshot, I will show the example of the contents of the app. These are the content of the courses... The codes are represent different subject. In the subject, they already...
1 comment
Read more